NiO particles with Ca and Mg based additives produced by spray- drying as oxygen carriers for chemical-looping combustion

AbstractChemical-looping combustion is a two-step combustion process where CO2 is obtained in a separate stream, ready for compression and sequestration. The technique involves two interconnected fluidized bed reactors, with a solid oxygen carrier circulating between them. Results of reactivity experiments with 24 different oxygen carriers, based on NiO with NiAl2O4 and/or MgAl2O4 and produced with spray-drying, are presented. The investigation revealed that oxygen carriers supported by MgAl2O4, or where a small amount of MgO was added, displayed an increased fuel conversion when compared to oxygen carriers of NiO supported by NiAl2O4

Influence of spray drying suspension on the morphology of Fe-based oxygen carriers for chemical looping

Chemical looping reforming (CLR) and chemical looping combustion (CLC) are promising technologies with inherent CO2 capture for transforming fuels into syngas and energy respectively. Circulating oxygen carriers (OC) are used to transfer oxygen from mostly air to the fuel inside the process. Over the past years a variety of materials have been proposed for the role of oxygen carriers, ranging from bulk mineral powders to oxygen carrier particles engineered for shape, size and composition. Iron based materials are very promising and cost effective candidates with minor impact on the environment as compared to the toxic Ni-based OCs. Granulation by the industrial spray-drying technique is suitable for producing oxygen carrier particles with high sphericity and dimensions fit for the fluidized-bed reactors of the CL-process. The lifetime of the oxygen carriers in these reactors however strongly depends on their mechanical properties (as measured by the crushing strength and the attrition resistance) which is related with their morphology and porosity. As this morphology depends on the spray drying suspension, the relation between the additives used in the iron-based suspension and the morphology of the spray-dried particles is investigated in this work [1]. The influence of the concentration of the binder, dispersing agent and solids in the spray-drying suspensions and the intensity of the milling procedure on the morphology and microstructure of the resulting particles is studied by Hg-porosimetry, tapped density, optical microscopy and SEM. A controlled sintering treatment is used during post-processing of these spray-dried particles in order to further improve their mechanical properties before investigating their performance as oxygen carriers in the chemical looping process

Oxygen-Carrier Development of Calcium Manganite–Based Materials with Perovskite Structure for Chemical-Looping Combustion of Methane

The present work is related to the upscaling of calcium manganite–based oxygen-carrier materials, which have a perovskite structure, both with respect to the use of inexpensive raw materials, i.e., instead of pure chemicals, and the upscaling of production to multitonne batches. Results are presented from the two different stages of material development, i.e., raw material selection and upscaling. The evaluation involves both operation in chemical-looping combustor units of 300 W and 10 kW, and material characterization. In the latter unit, the gas velocities in the riser and in the grid-jet zone of the gas distributor come close to gas velocities of industrial-scale units and, therefore, this unit is also used to assess particle lifetime. Results from the various chemical-looping combustion units and oxygen-carrier materials produced from various raw materials of both high and low purity show that very high degrees of fuel conversion can be reached while achieving very high oxygen-carrier lifetimes. The composition of the oxygen-carrier materials seems robust and flexible with respect to the precursors used in its manufacturing

Sustainable Attrition-resistant oxygen carriers for chemical looping reforming by spray drying

Chemical looping reforming (CLR) and chemical looping combustion (CLC) are promising technologies with inherent CO2 capture for transforming fuels into syngas and energy respectively. Circulating oxygen carriers (OC) are used to transfer oxygen from mostly air to the fuel inside the process. Over the past years a variety of materials have been proposed for the role of oxygen carriers, ranging from bulk mineral powders to oxygen carrier particles engineered for shape, size and composition. A lot of attention has been focused towards the development of Ni-based oxygen carriers due to their good reactivity, conversion and mechanical stability. However the cost, susceptibility towards S-containing impurities and their toxicity are key drivers to develop Ni-free materials. Oxygen carriers based on Fe-oxides are promising because of their lower cost and diminished impact on health and environment. Nevertheless, they also need good thermo-chemo-mechanical properties and thus a sufficient lifetime to be applicable in industrial CL-processes. The longevity of the oxygen carriers in the coupled fluidised bed reactors can be limited by two factors, such as their fragmentation and attrition leading to smaller particles inhibiting their fluidisation as well as their chemical deactivation. Granulation by the industrial spray drying technique appears to yield oxygen carrier particles with high sphericity and good fluidization properties. In addition, a microstructure is obtained that on the one hand aims at thermo-chemo-mechanical integrity and high attrition resistance, and on the other hand at intimate contact between the solid and gaseous phases. However, spray-drying does not appear to be used for producing Fe-based OC thus far. This work emphasises the colloid chemistry of concentrated suspensions used for spray-drying, the development of Fe-based OC by granulation of primary raw materials and the subsequent processing and heat treatment of the oxygen carriers for hydrogen production by chemical looping. To reach the objectives, a systematic approach is used. At first the role of the preparation of the spray dry suspension and the granulation conditions on the morphology of the particles has been investigated. Secondly, the effect of the sinter process was studied. A correlation between tapped density, strength and attrition resistance of the heat-treated materials was observed. Finally, the chemical performance of these Fe-based oxygen carriers was examined in a small scale batch reactor. The chemical composition of the OC was (ex situ) monitored in view of the enhancement of the chemical properties and long term stability thereof by altering the composition and microstructure of synthesised oxygen carriers

Development of stable oxygen carrier materials for chemical looping processes : a review

This review aims to give more understanding of the selection and development of oxygen carrier materials for chemical looping. Chemical looping, a rising star in chemical technologies, is capable of low CO2 emissions with applications in the production of energy and chemicals. A key issue in the further development of chemical looping processes and its introduction to the industry is the selection and further development of an appropriate oxygen carrier (OC) material. This solid oxygen carrier material supplies the stoichiometric oxygen needed for the various chemical processes. Its reactivity, cost, toxicity, thermal stability, attrition resistance, and chemical stability are critical selection criteria for developing suitable oxygen carrier materials. To develop oxygen carriers with optimal properties and long-term stability, one must consider the employed reactor configuration and the aim of the chemical looping process, as well as the thermodynamic properties of the active phases, their interaction with the used support material, long-term stability, internal ionic migration, and the advantages and limits of the employed synthesis methods. This review, therefore, aims to give more understanding into all aforementioned aspects to facilitate further research and development of chemical looping technology

A numerical homogenisation strategy for micromorphic continua

Cellular materials are of special interest according to their peculiar mechanical properties. In this paper, special attention is paid to the simulation of size-dependent microtopological effects. We introduce a numerical homogenisation scheme for a two-scale problem dealing with a micromorphic continuum theory on the macroscale and a classical Cauchy continuum on the microscale. The transitions between both scales are obtained by projection and homogenisation rules derived from an equivalence criterion for the strain energy, also known as the Hill-Mandel condition

Fotochemie van tetra-N-butylammoniumhexacyanokobaltaat (III) in dichloormethaan

SIGLEKULeuven Campusbibliotheek Exacte Wetenschappen / UCL - Université Catholique de LouvainBEBelgiu

Fotochemie van tetra-N-butylammoniumhexacyanokobaltaat (III) in dichloormethaan

SIGLEKULeuven Campusbibliotheek Exacte Wetenschappen / UCL - Université Catholique de LouvainBEBelgiu